HPI | Horse Power Ignition
Digital CDI/ECU options:
 2 Curves
The CDI will have two additional wires that allow you to switch between two different ignition curves. Selecting the curve can be done by simply connecting or diconnecting these two wires, or by selecting the curve with a switch (image on the right).

Order code for the switch: 068V064
 2 Curves
 Programmable
Only for digital units. Draw your own ignition curve with our TuneBox software, and program it into the CDI with the interface. The TuneBox software is free, and the latest version can be downloaded from the link below.

Order code for the programmation kit (USB Interface and the latest version of the TuneBox software on a CD): 068V043

For more info, or to download the TuneBox software, click here.
 Programmable
 Powerjet
PowerJet is only available on digital CDI-units and can be set up with the TuneBox software. It is an exit which is able to draw 2 amperes to ground in 2 user defined RPM regions. This can be used to drive a valve or light at a desired RPM range.

This is an optional exit for most vehicles. If, however, the vehicle already uses this system, our CDIs will be equipped with this system as standard. This means no additional wires, as the system is implemented into the wiring loom or connector, as with the original CDI.

If the vehicle has no standard PowerJet installed, this exit comes as an extra wire. Users should build a valve system on their engines themselves.
 Powerjet
 Shift System
Shift Delay System (SD) is only available on digital CDI-units and allows to shift gears without clutch. The shift delay system will retard or interrupt the ignition momentarily to release the transmission load. In this moment the rider can shift up without throttling down.

The shift delay system comes as an additional 2 wire plug (with counterpart) and can be fully adjusted to be used with any input switch, which has to be installed by the user. Use TuneBox to set the SD for normal open or normal closed switches. Set the SD to retard the ignition 60° or to interrupt the ignition for a programmable period of time.
 Shift System
 Throttle position
Throttle Position Sensor (TPS) is only available on digital CDI-units. It is an optional input which will determine which advance curve will be selected. With TuneBox you will be able to draw 6 different advance curves. The TPS will then decide which one is activated.

Use the TPS in combination with the curve switch:
• Position 1; The CDI will ignore the TPS. The CDI will then select curve 1, which can be used for sound tests.
• Position 2; The TPS signal will determine which curve is selected. Low throttle selects curve 2, full throttle selects curve 6.

If the vehicle has no standard TPS installed, this input comes as an additional 3 wire plug. Users should build a TPS on their system themselves.
 Throttle position



CD5006D-6CF-S
DIGITAL UNIT

list of all CDI / ECU / TCIs

€305

All prices are ex. 21% VAT

REPLACES OEM PART CODES: 250216-01 / 250224-01 / 250217-01 / 250225-01 / 250251-01 / 250295-01 / 250269-01 / 250288-01 / 250216-02 / 250226-01 / 250224-02 / 250225-02 / 250293-01 / 250253-01 / 250289-01 / 250226-02 / 250224-03 / 250225-03 / 250254-01 / 250290-01 / 250310-01
THIS PARTNUMBER INCLUDES:

CD5006D-6CF-S

Shift System Connector

Throttle Position Connector
HusabergFC 400 (1999) 400cc
FE 400 (1999-2000) 400cc
FE 400e (1999-2003) 400cc
FS 400c (2001-2002) 400cc
FS 400e (2001-2003) 400cc
FX 400 (2000) 400cc
FC 470 (2001-2002) 470cc
FC 470e (2001-2002) 470cc
FX 470e (2001-2002) 470cc
FC 500 (1999-2000) 500cc
FE 500 (1999-2000) 500cc
FE 500e (1999-2000) 500cc
FX 500 (2000) 500cc
FE 501e (2001-2003) 501cc
FC 550 (2001-2003) 550cc
FC 600 (1999-2000) 600cc
FE 600 (1999-2000) 600cc
FE 600e (1999-2000) 600cc
FX 600 (2000) 600cc
FE 650e (2001-2003) 650cc
FS 650c (2001-2003) 650cc
FS 650e (2001-2003) 650cc
FX 650e (2001-2003) 650cc